Category Archives: ALL
Front panel CPU Board
Front panel consist of two boards. One of them is CPU board with main microcontroller AtXMEGA128A3U-AU, main dial optical encoder BOURNS, mechanical encoders, dual concentric potentiometer AF/RF. This board holds LCD&switch PCB.
RGO ONE latest specification sheet
This is latest specs sheet
Meanwhile you can see number three in action -making QSO with german special event station
RGO ONE serial number 190003 (number three)
Serial number three (190003) RGO ONE HF transceiver is alive!
Yesterday we finished assembly and adjustment process so it is ready to go.
First production lot (10pcs.) will be with serials between 190003 and 190012. We will reserve number one and number two for our two samples which will be updated to the current version later.
RGO ONE internal view
Main Board (MB)
RGO ONE Main Board (MB) or so called mother board fits all connectors on the rear panel, power supply, I/O controller (second CPU). MB is also intended to be a chassis for all RF boards and options, as long as “cable harness” and board interconnections.
The board has the following components on it:
– I/O micro controller U5, DAC U7, external fan control – U8, T12, signal multiplexer U9, 3.3V LDO regulator chip U4
– USB FTDI chip F1
– I/O connectors at the back side, daughter board connectors, power on/off switch, level converters, 5V,8V LDO regulators
PCB component side (bottom):
PCB component side (bottom) values:
PCB top:
LO board
LO board provides all oscillator signals needed for signal conversion and mixing. The board consists of the following components:
– LO first oscillator realized by U2 – SI570 (570CAC000141DG), 3 switchable low pass filters: 10.8-15MHz; 15-24MHz; 24-39MHz. Filter switching is performed by I2C chip PCA9536
– 9MHz generators – U3 (SI5351) BFO, CW sidetone, beeps, U1 (SA-612) balanced mixer which acts as CW/SSB monitor product detector, digital poteniometer – U7 (MCP4018-502E)
– Tone shaping, (tones on/off ) circuitry – T1,T2,T5
– Temperature compensation oven made by thermo resistor R14 and T3,T4
PCB component side
In order to achieve good results with low harmonic content and stability – PCB board is well shielded in two component metal tin can:
RX MIXER
RX MIXER standard is ADE-1 diode ring mixer. Here described is optional high dynamic range H-mode mixer.
The schematic and original H-mode mixer concept has been designed by Colin Horrabin G3SBI and further developed by Martein Bakker PA3AKE.
PCB component side
RF MIXER
RF MIXER board does all RX/TX signals on IF and operation frequencies.
On receive the signal comes on CX3 coaxial connector, then passes (or not) through input attenuator R10,R13,R14, then via switches come to BPF board. IF TRAP circuitry consists of L1, C7, C38. Then signal passes through U3 (ERA6SM) RX preamplifier (operator switchable). RX MIXER is on additional subboard and sits over RF MIXER board. 9MHz diplexer follows and then IF amplifier – U12 (ERA6SM). After some switching and attenuation signal comes to the first crystal filter – 2.7kHz then to CX6 coaxial connector and IF/AF board.
On transmit the signal from SSB GEN board through CX7 connector passes through crystal filter and after TX/RX switch to a pin diode D1 attenuator. It is driven by ALC circuitry performed by U16 and T4.
U11 is TX mixer which is fine balanced by R62 and impedance matched by L10,L18 wide band transformers. Output mixed signals are further filtered by BPF board and amplified by U3 and U9. Output attenuator R4,R5,R6 is following then via CX4 signal goes to linear amplifier PA55W board.
Component side PCB
Component side values
RGO ONE Power amplifier module
LO /local oscillator/ BFO tones board
Here is some pictures of LO board – ready and shielded
Copper straps are added in order to improve ground on the board
RGO ONE building process
By now all printed circuit boards are ready and populated. We have also some boards – completely tested and aligned:
1. IF/AF board
2. RF MIXER board
3. LO/tones board.
4. Front panel assembly – CPU, LCD/switches boards
5. Both crystal filters – 2,7kHz and the optional 4 pole variable filter
Still working on back panel module – PA and LPF. BPF,SSBGEN are being carefully tested on the bench
